Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
The publisher is making several good points related to Installing A Bathtub in general in this post underneath.
Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging project. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall to remove the old bathtub and also place the new bathtub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub and also set in the new one. Ensure you have certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will certainly assist you mount a new bathtub in your bathroom if you have actually already gotten a new tub and do not require to alter the plan of your previous water supply pipes.
Your devices as well as material checklist must comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making certain that the washing machines are in area in between the tap and the sink. Secure the faucet in position with the producer provided backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap ports. The former type needs to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Making use of the two wood boards under its feet, put the bathtub in the needed placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Load the tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait until the bath tub has been used at the very least when as this will resolve it into its last setting.
Preparing for the Installment
First of all, the sustaining framework provided with the bath should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with moisture and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components as well as installations. They are offered in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealant can crack fairly early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the market. It is a good idea to fit the tiles using water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our part about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking time to read our content. Loved our blog entry? Please share it. Let other people find it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Plumbing SOS? Reach out! Report this page